Richtig.
Hab´s jetzt auch deaktiviert bekommen.
Die Probleme sind allerdings die selben :(
seeeeeeehr langsam und machmal sogar Verbindungsabbrüche.
Druckbare Version
Richtig.
Hab´s jetzt auch deaktiviert bekommen.
Die Probleme sind allerdings die selben :(
seeeeeeehr langsam und machmal sogar Verbindungsabbrüche.
guten morgen marco ;)Zitat:
Zitat von DefiSchwein
wenn du deinen screenshot nochmal genau anschaust (ich gehe davon aus, daß dieser screenshot nicht der alte, sondern der mit IPv6 deaktiviert ist), dann wirst du sehen, daß IPv6 immer noch aktiviert ist. ein kollege von mir hatte das gleiche problem. versuche es mal folgendermaßen:
du kannst wahrscheinlich auch alle auf eins setzen, aber versuche es erstmal so.Zitat:
Disabling IPv6
Unlike Windows XP, IPv6 in Windows Vista cannot be uninstalled. To disable IPv6 on a specific connection, you can go to the Network Connections folder, obtain properties of the connection and clear the check box next to the Internet Protocol version 6 (TCP/IPv6) component in the list. This method disables IPv6 on your LAN interfaces and connections, but does not disable IPv6 on tunnel interfaces or the IPv6 loopback interface.
To selectively disable IPv6 components and configure behaviors for IPv6 in Windows Vista, create and configure the following registry value (DWORD type)
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Servic es\tcpip6\Parameters\DisabledComponents
DisabledComponents is set to 0 by default.
The DisabledComponents registry value is a bit mask that controls the following series of flags, starting with the low order bit (Bit 0):
Bit 0 Set to 1 to disable all IPv6 tunnel interfaces, including ISATAP, 6to4, and Teredo tunnels. Default value is 0
Bit 1 Set to 1 to disable all 6to4-based interfaces. Default value is 0
Bit 2 Set to 1 to disable all ISATAP-based interfaces. Default value is 0
Bit 3 Set to 1 to disable all Teredo-based interfaces. Default value is 0
Bit 4 Set to 1 to disable IPv6 over all non-tunnel interfaces, including LAN interfaces and *Point-to-Point Protocol (PPP)-based interfaces. Default value is 0
Bit 5 Set to 1 to modify the default prefix policy table to prefer IPv4 to IPv6 when attempting connections. Default value is 0
To determine the value of DisabledComponents for a specific set of bits, construct a binary number consisting of the bits and their values in their correct position and convert the resulting number to hexadecimal. For example, if you want to disable 6to4 interfaces, disable Teredo interfaces, and prefer IPv4 to IPv6, you would construct the following binary number: 101010. When converted to hexadecimal, the value of DisabledComponents is 0x2A.
The following table lists some common configuration combinations and the corresponding value of DisabledComponents.
Configuration combination DisabledComponents value
Disable all tunnel interfaces 0x1
Disable 6to4 0x2
Disable ISATAP 0x4
Disable Teredo 0x8
Disable Teredo and 6to4 0xA
Disable all LAN and PPP interfaces 0x10
Disable all LAN, PPP, and tunnel interfaces 0x11
Prefer IPv4 over IPv6 0x20
Disable IPv6 over all interfaces and prefer IPv4 to IPv6 0xFF
You must restart the computer for the changes to the DisabledComponents registry value to take effect.
HHH, der hofft daß es so klappt
Hm,
hört sich ja spannend an aber wo kann ich das denn alles machen??? :gruebel: :gruebel:
steht doch in dem artikel :ratlos:Zitat:
Zitat von DefiSchwein
du mußt das über die registry machen -> start/run anklicken und dann in die eingabezeile regedit tippen. dann geht der registryeditor (sieht aus wie der explorer auf), auf den angegebenen pfad gehen und die bits entsprechend setzen.
HHH
Zitat:
Zitat von HHH
Hm,
aber dieses hier: HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Servic es\tcpip6\Parameters\DisabledComponents
gibts bei mir nicht. :gruebel: (siehe Bild1)
Hab nochmal geschaut. Bei meiner Breitbandverbindung ist Ip6 deaktiviert (Bild2) aber wenn ich das in der LAN Verbindung (Bild3) deaktiviere klinkt sich sofort das Internet aus und lässt mich auch nicht mehr einwählen. :crybaby:
ich kann das leider gerade nicht nachprüfen, da ich mittlerweile wieder zuhause bin (hier habe ich kein vista) und nur wegen dir hier auf zähne vorbeischaue. aber lt. deinem screenshot ist im LAN die IPv6 noch aktiviert. deaktiviere die mal und schau nach wie dann die registry aussieht.
HHH
Hm, negativ.
Auch dann kommt so ein Eintrag dort nicht.
Hab auf 2 anderen Computerforen noch gepostet und keiner weiß was es ist. Reuden Vista :axt:
hast du nach der deaktivierung von IPv6 einen restart gemacht? wenn nein, dann mach das doch mal und schaue ob dann der entsprechende pfad vorhanden ist.Zitat:
Zitat von DefiSchwein
HHH
Als ich mich bei meinem jetzigen Internet-Provider anmeldete, schickten sie mir mit den Unterlagen ein Faltblatt, in dem steht, wie man die Verbindung manuell einrichtet. Unter anderem wird da auch der Wert MTU (Maximum Transfer Unit) genannt, welcher auf 1454 gestellt werden soll.
Windows hat immer einen MTU-Default-Wert von 1500 eingestellt. Möglich wäre es, dass bei deinem Router (den du vorher genutzt hast) der MTU-Wert von 1500 wegverändert wurde, du aber vergessen hast, dass auch bei deinem PC dieser Wert eingestellt werden muss, wenn du das DSL-Modem direkt anschließt. Bevor du dich auf die Suche machst oder fragst, wo du diesen Wert im PC einstellst, solltest du lieber herausfinden, ob MTU bei dir überhaupt eine Rolle spielt. Siehe Unterlagen deines DSL-Providers.